Irrigation system installation

Get acquainted with the installation of the GRAAS iRigator automatic irrigation system

Installing the GRAAS iRigator automatic irrigation system is very simple, and anyone can do it.


When purchasing the GRAAS iRigator, you can choose between two versions of the device – GSM or Wi-Fi. The Wi-Fi version is used at home in greenhouses with a strong and stable Wi-Fi internet connection. The GSM version is intended for greenhouses without Wi-Fi access. GSM is often used in suburban gardens or private homes where the Wi-Fi signal in the greenhouse is too weak to ensure stable system operation. GRAAS always recommends choosing the GSM version. The WIFI version is used at home with a good and stable WIFI internet connection in the greenhouse. The GSM version is used in greenhouses without WI-FI access. The GSM version is often used in country gardens or private houses when the WI-FI signal in the greenhouse is too weak to ensure stable operation of the system. GRAAS always recommends choosing the GSM version.

GRAAS iRigator GSM

    The GSM version is used in greenhouses where there is no Wi-Fi signal or it is very weak. The GSM version requires a WorldWide plan, which normally costs €4.90/month, but when purchasing the irrigation system now you will receive a one-year WorldWide plan subscription free of charge!


    After unpacking the product, you need to follow these steps in the given order:


    1. Hang up the device.

    2. Lay out the water hoses for each zone.

    3. Puncture holes in the main zone hose and connect thin hoses to each plant stem.

    4. Attach the hoses to the device’s water outlets.

    5. Connect the power cable and switch on the device (The device turns on immediately once connected to the network).

    6. Wait about 1 minute for the device to connect to the server.

    7. Open the GRAAS app (an email with the download link for the app is sent separately).

    8. In the GRAAS app, open the “GRAAS iRigator” device.

    9. In the app, go to settings and press “bleed the system.”

    10. Connect the water source and turn on the water.

    11. Monitor each zone. Once you are sure that water flows through all outlets, press “finish system bleeding.”



    After unpacking the product, you must perform the following steps in the order indicated:


    1. Hang the device.

    2. Lay out the water hoses for each zone.

    3. Punch holes in the main zone hose and connect thin hoses to each plant stem.

    4. Close the hoses on the water outlets of the device.

    5. Connect the power cable and turn on the device (The device turns on immediately, only connected to the network).

    6. Wait about 1 minute for the device to connect to the server.

    7. Open the GRAAS app (a letter with a link to download the app is sent in a separate email).

    8. In the GRAAS app, open the GRAAS iRigator device.

    9. In the app, go to settings and press "clear system".

    10. Connect the water source and run the water.

    11. You must monitor each zone. After making sure that water is flowing through all the outlets, press "end system drain".


    GRAAS iRigator WI-FI

      The WI-FI version is suitable for greenhouses that are near the house and have a good WI-FI signal. If you choose the WI-FI version and notice that the signal in the greenhouse is not strong enough, you can later change the device version to GSM by contacting us.


      After unpacking the product, you must perform the following steps in the order indicated:


      1. Connect the product to the computer using the included USB cable.

      2. Download the GRAAS WI-FI application to your computer and open it.

      3. Enter the WI-FI access name and password and press "send".

      4. Wait until you see "connection successful" in the application window.

      5. Disconnect the device from the computer and take it to the greenhouse.

      6. Hang the device.

      7. Lay the water hoses for each zone.

      8. Punch holes in the main zone hose and connect thin hoses to each plant stem.

      9. Close the hoses on the water outlets of the device.

      10. Connect the power cable and turn on the device (The device turns on immediately, only connected to the network).

      11. Wait about 1 minute for the device to connect to the server.

      12. Open the GRAAS app.

      13. In the GRAAS app, open the GRAAS iRigator device.

      14. In the app, go to settings and press "clear system".

      15. Connect the water source and run the water.

      16. You must monitor each zone. After making sure that water is flowing through all the outlets, press "end system drain".